• Home
  • Lifting-Stations

ZEHNDER PUMPEN – MADE IN GERMANY

jdjd
ee

SWH 100 series

  • Pre-assembled ready for connection – easy installation
  • Polypropylene container with 20 litres capacity and up to 10 litres switching volume
  • Switching device integrated in lid with audible high water alarm signal
  • Potential-free contact for external alarm or washing machine stop
  • Pump fixed on lid for easy cleaning and maintenance
  • Prepared shower inlet DN 50 usable on both sides (container bottom edge til middle of shower inlet only 80 mm)
  • Operation temperature 40°C (short-term 90°C)
  • Pressure outlet 1 ¼“ FPT with integrated non-return valve
  • Active carbon filter for container ventilation
  • Protection grade IP 57 – temporary submersible
ee

UFB 200 series

  • Polyethylene container with 35 litres capacity and up to 20 litres switching volume
  • Built-in waste water pump ZPK with float switch
  • Connection for air vent and cable gland DN 50 (HT)
  • Inlet connection piece DN 50 is included – installable by drilling a hole in the container
  • Pressure outlet 1 ¼“ with integrated non-return valve
  • Operation temperature 40°C (short-term 90°C)
  • Protection grade IP 68 – fully submersible
ee

SWH-F 500 series

  • As Lifting unit for grease separators.
  • Polyethylene container with 135 litres capacity and up to 75 litres switching volume
  • Simplex units with submersible waste water pump ZPK with float switch
  • Duplex units with 2 pumps ZPK and control unit with pneumatic level control ZPS2
  • Motor housing and shaft made of stainless steel, suction strainer, impeller and pump housing made of polypropylene
  • Piping made of PVC with external non-return valves and pressure outlet 1 ¼“ FPT
  • Operation temperature 40°C (short-term 90°C)
  • Protection grade IP 57 – temporary submersible
ee

Gerios

  • Optimized high-performance cutting system made of corrosion-resistant special steel 1.4112 with particular high hardness, wear resistance and cutting performance
  • Tank made of ABS for direct connection to a free-standing toilet with minimum inlet height
  • Tank made of ABS for direct connection to a free-standing toilet with minimum inlet height
  • Tank ventilation via activate carbon filter; optional ventilation via DN 40 pipe
  • Robust, wet-installed pump
  • Integrated alarm signal in case of malfunction
  • Pressure outlet 11/4″ FPT with integrated non-return valve on top; outlet horizontal or vertical (90° bend)
  • Max. medium temperature 40°C – short-term max. 60°C protection grade IP 68 – fully submersible

Sanicubic 2 Classic

Sanicubic 2 Classic are 2-pump stations designed for the lifting of waste water from single-family houses, pool-houses, kitchens etc. They benefit from the Pro X K2 maceration technology evacuating waste water through a small 50 mm diameter ext. pipe. The two pumps work alternately. The 5 inlets, 2 of which are low, allow great flexibility in the installation of sanitary equipment.

ee

Performances

  • Total manometric head: 13 m
  • Max. flow rate: 15 m3/h

Product Benefits

  • Inbuilt tank capacity of 45 ltrs.
  • Installation without clearance
  • Accessibility for maintenance purposes
  • Alternate operation of the 2 pumps
  • 5 inlets, including 2 low ones
  • Low latch
  • Direct and secure access to the pumps
  • Optional SFA Connect mobile application with SMART version
ee

Kompaktboy

  • Polyethylene container with 55 litres capacity and up to 45 litres switching volume
  • Vortex pumps with high efficiency and low operation noise
  • Mechanical seal and shaft seal with intermediate oil chamber
  • Inlets: 3 x DN 100, 3 x DN 50, 1 x DN 50/100
  • Additional connections 1 ½“ for manual diaphragm pump
  • Air vent DN 70 (Ø 75mm)
  • Operation temperature max. 55°C
  • Operating mode S3 – 25%
  • Protection grade IP 68 – fully submersible
ee

Kompaktboy Duplex

  • Polyethylene container with 150 litres capacity and up to 80 litres switching volume
  • Vortex pumps with high efficiency and low operation noise
  • Mechanical seal and shaft seal with intermediate oil chamber
  • Inlets: 2 x lateral DN 100, 1 x lateral DN 50, 1 x back DN 100 and 1 x top DN 50/100
  • Additional connections 1 ½“ for manual diaphragm pump
  • Air vent DN 70 (Ø 75mm)
  • Operation temperature max. 55°C
  • Operating mode S3 – 25%
  • Protection grade IP 68 – fully submersible
ee

Boy

  • Polyethylene container with 140 litres capacity and up to 70 litres switching volume
  • Vortex pump with high efficiency
  • Mechanical seal and shaft seal with intermediate oil chamber
  • Inlets: 2 x DN 100
  • Additional connections 1 ½“ for manual diaphragm pump
  • Air vent DN 70 (Ø 75mm)
  • Operation temperature max. 55°C
  • Operating mode S3 – 25%
  • Protection grade IP 68 – fully submersible
ee

Boy Duplex

  • Polyethylene container with 200 litres capacity and up to 100 litres switching volume
  • Vortex pumps with high efficiency
  • Mechanical seal and shaft seal with intermediate oil chamber
  • Inlets: 2 x lateral DN 100, 1 x top DN 100/DN 150
  • Additional connections 1 ½“ for manual diaphragm pump
  • Air vent DN 100 (Ø 110mm)
  • Operation temperature max. 55°C
  • Operating mode S3 – 25%
  • Protection grade IP 68 – fully submersible
ee

W 80

  • Polyethylene container with 350 litres capacity and up to 175 litres switching volume
  • Vortex pump with large solids handling
  • Mechanical seal and shaft seal with intermediate oil chamber
  • Pump housing with cast-on outlet bend DN 100
  • Lateral inlet with loose-type flange DN 100
  • Additional connection 1 ½“ for manual diaphragm pump
  • Air vent with loose-type flange DN 100 (Ø 110 mm)
  • Operation temperature max. 55°C
  • Operating mode S3 – 25%
  • Protection grade IP 57 – fully submersible
ee

W 80 Duplex

  • Polyethylene container with 480 litres capacity and up to 270 litres switching volume
  • Vortex pump with large solids handling
  • Mechanical seal and shaft seal with intermediate oil chamber
  • Pump housing with cast-on outlet bend DN 100
  • Lateral inlet with loose-type flange DN 100
  • Additional connection 1 ½“ for manual diaphragm pump
  • Air vent with loose-type flange DN 100 (Ø 110 mm)
  • Operation temperature max. 55°C
  • Operating mode S3 – 25%
  • Protection grade IP 57 – fully submersible
ee

WUZ 100

  • Polyethylene container with 480 litres capacity and up to 270 litres switching volume
  • Single-channel impeller pump with fibre cutting insert and large solids handling
  • Mechanical seal (up to 4kW) or chilled casting seal (> 5 kW) and shaft seal with intermediate oil chamber
  • Pump housing with flanged outlet bend DN 100
  • Lateral inlet with loose-type flange DN 150
  • Additional connection 1 ½“ for manual diaphragm pump
  • Air vent with loose-type flange DN 100 (Ø 110 mm)
  • Star-delta-start for 7,5 kW unit
  • Operation temperature max. 55°C
  • Operating mode S3 – 25%
  • Protection grade IP 57 – temporarly submersible
ee

WUZ 100 Duplex

  • Polyethylene container with 1000 litres capacity and up to 500 litres switching volume
  • Two single-channel impeller pumps with fibre cutting insert and large solids handling
  • Mechanical seal (up to 4kW) or chilled casting seal (> 5 kW) and shaft seal with intermediate oil chamber
  • Pump housing with flanged outlet bend DN 100
  • Lateral inlet with loose-type flange DN 150
  • Additional connection 1 ½“ for manual diaphragm pump
  • Air vent with loose-type flange DN 100 (Ø 110 mm)
  • Star-delta-start for 7,5 kW unit
  • Operation temperature max. 55°C
  • Operating mode S3 – 25%
  • Protection grade IP 57 – temporarly submersible